View source for Hard Drive Partition Scheme

{{MessageBox|
backgroundcolor	= #faa|
image	=Warning.png|
heading	=WARNING|
message = Recommend you disable/unplug ALL hard disks you do not want to put the system on to make it easier to partition. Data loss can result if you accidentally get confused about what disks are which or you make an error.}}
The Amahi team makes the following recommendations when partitioning drives in Amahi 7 or greater:

* Skip using [https://www.amahi.org/faq/does-amahi-support-lvm Logical Volume Management (LVM)], which creates added complexity for inexperienced users, in particular if there are disk failures.
* Do not make a separate /home partition. Amahi does not recommend use of /home for storage for users
* Allocate the majority of hard drive space in the / (root) partition.
* Do not add extra drives while installing.   recommend you do that later after the system is up and running successfully using [[Adding_a_second_hard_drive_to_your_HDA|adding a second hard drive to your HDA]] as a guide.
* The majority of space, to be used by file shares is set up to be at ''/var/hda/files'', which typically resides in the root partition.
* If you plan to use the [[Greyhole]] drive pooling technology, keep in mind that by default the Greyhole "[[Greyhole_landing_zone|Landing Zone]]" will be located in the root partition. This needs to have enough space to accommodate the single largest transaction that you plan or foresee you will make.

= How to Partition=
At the partitioning point of the Fedora installer, you do this:
* Select '''INSTALLATION DESTINATION''' under ''STORAGE'' section.
* Verify the correct drive is selected, then choose '''Done'''.
* Ensure '''Partition scheme''' reflects ''Standard Partition''.
* Choose ''I want to review/modify my disk partitions before continuing'' and select '''Continue'''.
* When prompted with '''INSTALLATION OPTIONS''', select ''Custom partitioning''.
* Choose each partition and select the '''minus''' (-) to remove them individually until all the partitions have been removed.
# If prompted ''Are you sure you want to delete all the data on...'', choose '''Delete it'''
# Ensure ''Delete all other filesystems in the Unknown root as well'' is selected.
* You should now see the message ''You haven't created any mount points for your installation yet''.
* First we need to make the ''Swap''.  Click on the plus (+) and a window will appear:
# Choose '''Mount Point''' of ''Swap''.
# Enter '''Desired Capacity''' based on the chart below.
# Select '''Add mount point'''.
::'''NOTE:''' The recommended size of a swap partition depending on the amount of RAM in your system.
::{|class="wikitable"
!System RAM
!Recommended swap space
|-
|< 2GB
|2 times the amount of RAM
|-
|> 2GB – 8GB
|Equal to the amount of RAM
|-
|> 8GB – 64GB
|0.5 times the amount of RAM
|-
|> 64GB
|4GB of swap space
|}
* Next is ''/boot''.  Click on the plus (+) and a window will appear:
# Choose '''Mount Point''' of ''/boot''.
# Enter '''Desired Capacity''' of ''500MB''.
# Select '''Add mount point'''.
* The last one is the ''/'' (root).  Click on the plus (+) and a window will appear:
# Choose '''Mount Point''' of ''/''.
# Enter '''Desired Capacity''' of the amount of remaining disk space (this is displayed at the bottom of the installer window)
# Select '''Add mount point'''.
* Review the partition scheme and if it looks ok, choose '''Done''' and select '''Accept changes'''.


You can now continue with the install as normal.

= Example =
For a system with 1GB RAM and 10GB hard drive, the following settings would apply for '''Desired capacity''':
* Swap = 2GB
* /boot = 500MB
* / = 7.73GB
	

Reference:  [http://docs.fedoraproject.org/en-US/Fedora/20/html/Installation_Guide/s2-diskpartrecommend-x86.html Fedora Recommended Partitioning Scheme]