Latest revision as of 11:27, 15 July 2011

Redirect to:

Amahi Plug Edition

Note: Most of this information is duplicated elsewhere. It needs to be verified and removed as necessary.

See Amahi_Plug_Edition for installation and supported devices.

Misc Notes

restarting rpm db in chrooted environment:

bash code
`rm /var/lib/rpm/__db* rpm --rebuilddb -vv`

@@ Line 1: / Line 1: @@
+#REDIRECT [[Amahi_Plug_Edition]]
+'''Note: Most of this information is duplicated elsewhere.  It needs to be verified and removed as necessary.'''
+See [[Amahi_Plug_Edition | Amahi_Plug_Edition]] for installation and supported devices.
+= Misc Notes =
+* restarting rpm db in chrooted environment:
+{{Code|rm /var/lib/rpm/__db*
+rpm --rebuilddb -vv}}
+<!--* May need to add the following line to /etc/resolv.conf if you have DNS issues:
+ nameserver 8.8.8.8-->
+<!--  OLD NOTES
 * 2 stop bits to get the bootloader to recognize keyboard and stop autobooting
 * speed: 115200 /dev/ttyUSB1
@@ Line 6: / Line 25: @@
 * rpms installed for amahi: httpd, ruby, samba,
 * build hdactl, hda-platform, install (with --nodeps)
-Missing deps in the installer:
-* httpd, samba, cadaver, bind-utils
 RPMs not available from the mirrors:
 * hda-greyhole
+* cadaver
 * rubygem-gd2 - actually - is this one necessary?
+* ruby-RMagick
-Other:
-* VPN does not work (had to turn it off in servers). This could be due to the kernel not having all that it needs for TUN/TAP?:
-      Cannot allocate TUN/TAP dev dynamically
-* Greyhole not working - hda-greyhole needed
-* crontab does not appear to be working
-* had to add with noatime in / to prevent flash burnout
-* should control monit - it keeps on pounding the flash with messages in /var/log/monit
-* would like to add swap to flash based drives
-* mt-daapd and amahi-transmission are dying
-= Getting it Going =
-Here are the steps to make it boot from USB
-* General [http://fedoraproject.org/wiki/Architectures/ARM/SheevaplugUSB directions]
-* get the rootfs-f12.tar.bz2 from
-     http://ftp.linux.org.uk/pub/linux/arm/fedora/rootfs/
-* Connect the JTAG module and connect the USB side to a terminal emulator
-* Putty for windows (Serial)
-* gtkterm for linux (use 2 stop bits!)
-* Reset the device from the JTAG module
-* At the terminal, press enter a couple of seconds after boot to prevent it booting to the flash
-* There are some commands to make it permanently boot off USB:
-          setenv mainlineLinux yes
-          setenv arcNumber 2097
-          setenv bootargs_root 'root=/dev/sda1 rootdelay=15'
-          setenv bootcmd_usb 'usb start; ext2load usb 0:1  0x6400000 /boot/uImage-2.6.30-sheevaplug'
-          setenv bootcmd 'setenv bootargs $(console) $(bootargs_root); run bootcmd_usb; bootm 0x6400000'
-          saveenv
-          reset
-= Amahi Install =
 * ssh into the plug
@@ Line 66: / Line 52: @@
 * And last but not least, get the installer going by accessing it with a browser:
-        <code><nowiki>http://plug:2000</nowiki></code>
+        <code><nowiki>http://your_ip_address:2000</nowiki></code>
 * input the install code and install!
 * NOTE: it may be better to
-* report bugs!
+* report bugs!-->
-= Reporting issues =
-These are mostly what matter for debugging:
-* <code><small>/root/hda-install.log</small></code>
-* <code><small>egrep -v 'POST|GET|progress' /tmp/amahi-ruby-install.log</small></code>

Amahi Wiki

Links

Personal tools

Navigation

Tools

Difference between revisions of "Plug notes"

Latest revision as of 11:27, 15 July 2011

Misc Notes