Difference between revisions of "Airport express"

From Amahi Wiki
Jump to: navigation, search
Line 8: Line 8:
 
# Create a DHCP Reservation (static IP): enter your HDA MAC address and IP address
 
# Create a DHCP Reservation (static IP): enter your HDA MAC address and IP address
  
Note that if the Airport Administration tool forces you to have at least two IP in the DHCP address pool (i.e. if, when entering the same IP address in Ending Address, it adds one to it), it should work fine two. You'll just need to create a second DHCP reservation, and enter any fake MAC address (aa.bb.cc.dd.ee.ff for example).
+
 
 +
:'''NOTE:'''  If the Airport Administration tool forces you to have at least two IP in the DHCP address pool (i.e. if, when entering the same IP address in Ending Address, it adds one to it), it should work fine two. You'll just need to create a second DHCP reservation, and enter any fake MAC address (aa.bb.cc.dd.ee.ff for example).
  
 
This will basically allow the DHCP server to only give out one IP address, and it will only give it to your HDA (if your HDA is ever configured to use DHCP, which it shouldn't). All other DHCP requests will be ignored, allowing your HDA DHCP server to be used for all computers on your local network.
 
This will basically allow the DHCP server to only give out one IP address, and it will only give it to your HDA (if your HDA is ever configured to use DHCP, which it shouldn't). All other DHCP requests will be ignored, allowing your HDA DHCP server to be used for all computers on your local network.
  
Look at a more [http://discussions.apple.com/thread.jspa?threadID=121990 detailed explanation].
+
Refer to [http://discussions.apple.com/thread.jspa?threadID=121990 this site] for a detailed explanation.
  
 
BTW, it's much easier if you don't want NAT (i.e. if you have another router that does that), then you can disable both NAT and DHCP by choosing bridge mode.
 
BTW, it's much easier if you don't want NAT (i.e. if you have another router that does that), then you can disable both NAT and DHCP by choosing bridge mode.
 
You just can't disable DHCP alone.
 
You just can't disable DHCP alone.

Revision as of 01:02, 30 September 2015

Apple's Airport Express and Airport Extreme have some settings that make it hard to use with other networking devices, including your Amahi server.

This trick also applies to the AT&T Uverse routers that do not enable to control DHCP by their users.

There is no option to disable the DHCP in the Airport admin tool, so what you need to do is trick it into being "more passive".

  1. Set DHCP Beginning Address and DHCP Ending Address to the same value: the IP address of your HDA
  2. Create a DHCP Reservation (static IP): enter your HDA MAC address and IP address


NOTE: If the Airport Administration tool forces you to have at least two IP in the DHCP address pool (i.e. if, when entering the same IP address in Ending Address, it adds one to it), it should work fine two. You'll just need to create a second DHCP reservation, and enter any fake MAC address (aa.bb.cc.dd.ee.ff for example).

This will basically allow the DHCP server to only give out one IP address, and it will only give it to your HDA (if your HDA is ever configured to use DHCP, which it shouldn't). All other DHCP requests will be ignored, allowing your HDA DHCP server to be used for all computers on your local network.

Refer to this site for a detailed explanation.

BTW, it's much easier if you don't want NAT (i.e. if you have another router that does that), then you can disable both NAT and DHCP by choosing bridge mode. You just can't disable DHCP alone.