Difference between revisions of "OpenVPN VPN Bridging"

From Amahi Wiki
Jump to: navigation, search
Line 1: Line 1:
 +
{{MessageBox|backgroundcolor = #FBB|
 +
image =Warning.png|
 +
heading =WARNING|
 +
message = This procedure could break networking, proceed with extreme caution!}}
 +
 +
'''NOTE:''' It is recommended that you shut down your current VPN before modifying configs and then restarting it after you finish configuring it.
 +
 +
Here's the procedure you need to follow in order to have your VPN clients get IP addresses in the same subnet as your HDA. This will enable certain traffic like broadcast traffic used in autodetection of protocols like [[DLNA]] and DHCP, cross your VPN bridge.
 +
 +
For example, if you HDA's IP is 192.168.0.2, by default, connecting to it using an OpenVPN client will give your client computer an IP address like 10.8.0.x.
 +
The following procedure will change this so that your client will receive an IP address like 192.168.0.x. 
 +
 +
These steps need to be done as '''root''' user:
 +
{{Code|yum -y install bridge-utils
 +
nano /etc/openvpn/openvpn-startup}}
 +
Add this at the end of the file:
 +
{{Text|Text=
 +
<nowiki>#################################</nowiki>
 +
<nowiki># Set up Ethernet bridge on Linux</nowiki>
 +
<nowiki># Requires: bridge-utils</nowiki>
 +
<nowiki>#################################</nowiki>
 +
 +
br<nowiki>=</nowiki>"br0"
 +
tap<nowiki>=</nowiki>"tap0"
 +
 +
eth<nowiki>=</nowiki>"eth0"
 +
eth_ip=`ifconfig <nowiki>|</nowiki> grep -A 1 $eth <nowiki>|</nowiki> tail -1 <nowiki>|</nowiki> awk -F':' '{printf $2}' <nowiki>|</nowiki> awk '{print $1}'`
 +
eth_netmask=`ifconfig <nowiki>|</nowiki> grep -A 1 $eth <nowiki>|</nowiki> tail -1 <nowiki>|</nowiki> awk -F':' '{printf $4}' <nowiki>|</nowiki> awk '{print $1}'`
 +
eth_broadcast<nowiki>=</nowiki>`ifconfig <nowiki>|</nowiki> grep -A 1 $eth <nowiki>|</nowiki> tail -1 <nowiki>|</nowiki> awk -F':' '{printf $3}' <nowiki>|</nowiki> awk '{print $1}'`
 +
 +
openvpn --mktun --dev $tap
 +
 +
brctl addbr $br
 +
brctl addif $br $eth
 +
brctl addif $br $tap
 +
 +
ifconfig $tap 0.0.0.0 promisc up
 +
ifconfig $br $eth_ip netmask $eth_netmask broadcast $eth_broadcast
 +
ifconfig $eth 0.0.0.0 promisc up}}
 +
 +
 +
{{Code|nano /etc/openvpn/openvpn-shutdown}}
 +
Add this text to the file:
 +
{{Text|Text=#!/bin/sh
 +
 +
<nowiki>####################################</nowiki>
 +
<nowiki># Tear Down Ethernet bridge on Linux</nowiki>
 +
<nowiki>####################################</nowiki>
 +
 +
br<nowiki>=</nowiki>"br0"
 +
tap<nowiki>=</nowiki>"tap0"
 +
eth<nowiki>=</nowiki>"eth0"
 +
eth_ip<nowiki>=</nowiki>`ifconfig <nowiki>|</nowiki> grep -A 1 $br <nowiki>|</nowiki> tail -1 <nowiki>|</nowiki> awk -F':' '{printf $2}' <nowiki>|</nowiki> awk '{print $1}'`
 +
eth_netmask<nowiki>=</nowiki>`ifconfig <nowiki>|</nowiki> grep -A 1 $br <nowiki>|</nowiki> tail -1 <nowiki>|</nowiki> awk -F':' '{printf $4}' <nowiki>|</nowiki> awk '{print $1}'`
 +
eth_broadcast<nowiki>=</nowiki>`ifconfig <nowiki>|</nowiki> grep -A 1 $br <nowiki>|</nowiki> tail -1 <nowiki>|</nowiki> awk -F':' '{printf $3}' <nowiki>|</nowiki> awk '{print $1}'`
 +
 +
ifconfig $br down
 +
brctl delbr $br
 +
 +
openvpn --rmtun --dev $tap
 +
 +
if [ "$eth_ip" !<nowiki>=</nowiki> "" ]; then
 +
    ifconfig $eth $eth_ip netmask $eth_netmask broadcast $eth_broadcast
 +
fi}}
 +
 +
 +
{{Code|chmod +x /etc/openvpn/openvpn-shutdown
 +
nano /etc/openvpn/amahi.conf}}
 +
Remove the line that contains: ''dev tun''
 +
and replace it with this:
 +
{{Text|Text=mode server
 +
tls-server
 +
dev tap0}}
 +
And remove (or comment out) the lines that start with ''server'' and ''ifconfig-pool-persist''.
 +
 +
{{Code|iptables -A INPUT -i tap0 -j ACCEPT
 +
iptables -A INPUT -i br0 -j ACCEPT
 +
iptables -A FORWARD -i br0 -j ACCEPT
 +
service openvpn restart}}
 +
* In your OpenVPN client (such as Amahi HDAConnect for Windows users) configuration, change ''dev tun'' with ''dev tap''. You'll also need to add a line that will make the client IP static:
 +
{{Text|Text=ifconfig 192.168.0.x 255.255.255.0}}
 +
Replace "x" in the IP address above with address you want your client to use.
 +
 +
[[Category: VPN]]
 +
 +
 +
 +
 +
 +
 +
 +
<!--UNFORMATTED VERSION
 
{{MessageBox|backgroundcolor = #FBB|
 
{{MessageBox|backgroundcolor = #FBB|
 
image =Warning.png|
 
image =Warning.png|
Line 89: Line 181:
 
Replace "x" in the IP address above with address you want your client to use.
 
Replace "x" in the IP address above with address you want your client to use.
  
−
[[Category: VPN]]
+
[[Category: VPN]]-->

Revision as of 12:21, 12 April 2011

Warning.png WARNING
This procedure could break networking, proceed with extreme caution!



NOTE: It is recommended that you shut down your current VPN before modifying configs and then restarting it after you finish configuring it.

Here's the procedure you need to follow in order to have your VPN clients get IP addresses in the same subnet as your HDA. This will enable certain traffic like broadcast traffic used in autodetection of protocols like DLNA and DHCP, cross your VPN bridge.

For example, if you HDA's IP is 192.168.0.2, by default, connecting to it using an OpenVPN client will give your client computer an IP address like 10.8.0.x. The following procedure will change this so that your client will receive an IP address like 192.168.0.x.

These steps need to be done as root user:

bash code
​yum -y install bridge-utils nano /etc/openvpn/openvpn-startup​

Add this at the end of the file:

Text
​################################# # Set up Ethernet bridge on Linux # Requires: bridge-utils ################################# br="br0" tap="tap0" eth="eth0" eth_ip=`ifconfig | grep -A 1 $eth | tail -1 | awk -F':' '{printf $2}' | awk '{print $1}'` eth_netmask=`ifconfig | grep -A 1 $eth | tail -1 | awk -F':' '{printf $4}' | awk '{print $1}'` eth_broadcast=`ifconfig | grep -A 1 $eth | tail -1 | awk -F':' '{printf $3}' | awk '{print $1}'` openvpn --mktun --dev $tap brctl addbr $br brctl addif $br $eth brctl addif $br $tap ifconfig $tap 0.0.0.0 promisc up ifconfig $br $eth_ip netmask $eth_netmask broadcast $eth_broadcast ifconfig $eth 0.0.0.0 promisc up​


bash code
​nano /etc/openvpn/openvpn-shutdown​

Add this text to the file:

Text
​#!/bin/sh #################################### # Tear Down Ethernet bridge on Linux #################################### br="br0" tap="tap0" eth="eth0" eth_ip=`ifconfig | grep -A 1 $br | tail -1 | awk -F':' '{printf $2}' | awk '{print $1}'` eth_netmask=`ifconfig | grep -A 1 $br | tail -1 | awk -F':' '{printf $4}' | awk '{print $1}'` eth_broadcast=`ifconfig | grep -A 1 $br | tail -1 | awk -F':' '{printf $3}' | awk '{print $1}'` ifconfig $br down brctl delbr $br openvpn --rmtun --dev $tap if [ "$eth_ip" != "" ]; then ifconfig $eth $eth_ip netmask $eth_netmask broadcast $eth_broadcast fi​


bash code
​chmod +x /etc/openvpn/openvpn-shutdown nano /etc/openvpn/amahi.conf​

Remove the line that contains: dev tun and replace it with this:

Text
​mode server tls-server dev tap0​

And remove (or comment out) the lines that start with server and ifconfig-pool-persist.

bash code
​iptables -A INPUT -i tap0 -j ACCEPT iptables -A INPUT -i br0 -j ACCEPT iptables -A FORWARD -i br0 -j ACCEPT service openvpn restart​
  • In your OpenVPN client (such as Amahi HDAConnect for Windows users) configuration, change dev tun with dev tap. You'll also need to add a line that will make the client IP static:
Text
​ifconfig 192.168.0.x 255.255.255.0​

Replace "x" in the IP address above with address you want your client to use.





Retrieved from "https://wiki.amahi.org/index.php?title=OpenVPN_VPN_Bridging&oldid=38581"