Fedora 19 USB install

From Amahi Wiki
Jump to: navigation, search

This guidance is provided as an unsupported install of Amahi 7 on Fedora 19 using a USB flash drive. It requires manual configuration to install Amahi 7 and configure Greyhole. The Express CD officially supported install instructions can be found at here.

PREREQUISITES

Create USB image (Windows)

  • Insert USB flash drive into Windows computer.
  • Run UNetbootin
  • Select Fedora for Distribution
  • Choose the appropriate version depending on your system:
    • 19_Live (32-bit)
    • 19_Live_X64 (64-bit)
  • Verify at the bottom
    • Type is USB Drive
    • Drive listed is for your USB flash drive. If not, select the appropriate drive.
  • Once you are ready, choose OK. Please be patient as this may take a while since it downloads the files and then extracts them to the USB flash drive.
  • When UNetbootin finishes, select Exit and remove the USB flash drive.

Install Fedora

  • Insert the USB flash drive into your server.
  • Now boot your server using the USB flash drive. Some BIOS have function keys that allow you to choose the boot media. Others may require changes to the BIOS.
  • Select Start Fedora Live from the menu.
  • Once the Fedora has booted, you will have two options:
    • Try Fedora
    • Install to Hard Drive
  • Select Install to Hard Drive.
  • Configure the options as you desire, i.e. Time Zone, Hard Drive. When finished, select Begin Installation.
  • Now you will see the options to set a root password and/or create a user. You MUST do one of the following:
    • Set a root password and create a user.
    • Create a user and make it an administrator.
  • Once the install is finished, select Quit.
  • Finally we will need to reboot the machine (DO NOT remove the USB flash drive)
    • Choose the Live User at the top right of the screen
    • Select Power Off and then Reboot.
    • Once the login screen appears, you can remove the USB flash drive and log in using the password for the user set during install.


NOTE: Most commands from here on will need to be executed as a privileged user. Depending on how you configured the users at install, you may need to precede them with sudo (made user administrator). Otherwise, you will need to be root user.

Enable SSH (Optional)

We need to enable SSH for remote access. If you don't intend to access your HDA remotely inside or outside your network via SSH, you can skip this step.

  • Execute the following as a privileged user (precede commands with sudo if not run as root user):
systemctl start sshd.service
systemctl enable sshd.service

Connectivity (DNS)

Ensure you can connect to the internet before proceeding to Install Amahi 7 section.

  • Install network tools:
yum -y install net-tools
  • Next try pinging a web site such as google.com:
ping google.com
  • You should see something similar to the following (proceed to the Install Amahi 7 section):
PING google.com (74.125.225.2) 56(84) bytes of data.
64 bytes from ord08s12-in-f2.1e100.net (74.125.225.2): icmp_seq=1 ttl=51 time=17.6 ms
64 bytes from ord08s12-in-f2.1e100.net (74.125.225.2): icmp_seq=2 ttl=51 time=16.2 ms
64 bytes from ord08s12-in-f2.1e100.net (74.125.225.2): icmp_seq=3 ttl=51 time=15.1 ms
64 bytes from ord08s12-in-f2.1e100.net (74.125.225.2): icmp_seq=4 ttl=51 time=15.9 ms
  • If you did not get a successful ping, edit the following file:
vi /etc/resolv.conf
  • Add the following to the end of the file:
nameserver 208.67.222.222
nameserver 208.67.220.220
  • Restart the network:
systemctl restart network.service

Now check again and if you can access the internet, proceed to the next section. Otherwise, further troubleshooting will be required.

Install Amahi 7

Follow the guidance for Amahi 7 Full DVD starting with the Install Amahi section.

NOTE: If you need to add additional hard drives, refer to the guidance for adding additional drives. This includes procedures for the new 3 & 4 TB drives.

Install Greyhole (Optional)

Amahi application Greyhole UI provides this capablity.

Install Complete

Amahi 7 should be installed and working as designed. Recommend you reboot the HDA next to verify all is working correctly.

Customizations (Optional)

You can disable the GUI and boot headless. You can also remove the boot splash screen as well.

NOTE: All of the steps require privileged user environment (root user or precede commands with sudo).

  • Disable GUI on boot:
rm -rf /etc/systemd/system/default.target
ln -sf /lib/systemd/system/multi-user.target /etc/systemd/system/default.target
  • Restore GUI on boot:
rm -rf /etc/systemd/system/default.target
ln -sf /lib/systemd/system/graphical.target /etc/systemd/system/default.target
  • Remove boot splash:
    • Edit /etc/default/grub
    • Add # to beginning of GRUB_CMDLINE_LINUX line:
    • Rebuild GRUB menu:
grub2-mkconfig -o /boot/grub2/grub.cfg
  • Restore boot splash:
    • Edit /etc/default/grub
    • Remove # from beginning of GRUB_CMDLINE_LINUX line.
    • Rebuild GRUB menu:
grub2-mkconfig -o /boot/grub2/grub.cfg
  • You will need to reboot to complete the changes.
reboot


Reference: Disabling X Server on Fedora 17

Retrieved from "https://wiki.amahi.org/index.php?title=Fedora_19_USB_install&oldid=86296"