Difference between revisions of "Amahi 9 Install"

From Amahi Wiki
Jump to: navigation, search
Line 169: Line 169:
 
<br>
 
<br>
 
<ul>
 
<ul>
<li>Click '''[Expand]''' to show and '''[Collapse]''' to hide the instructions which will guide you through the Fedora 23 Server DVD installation with screen shots and commentary.<div class="mw-collapsible mw-collapsed">
+
<li>Click '''[Expand]''' to show and '''[Collapse]''' to hide the instructions which will guide you through the Fedora 23 Server DVD installation with screen shots and commentary.
 +
<div class="mw-collapsible mw-collapsed">
 
:'''NOTE:'''  Click '''[Expand]''' below each step to show a screen shot and '''[Collapse]''' to hide it.<br>
 
:'''NOTE:'''  Click '''[Expand]''' below each step to show a screen shot and '''[Collapse]''' to hide it.<br>
 
<u>Boot Screen</u>
 
<u>Boot Screen</u>

Revision as of 01:11, 1 February 2016

Warning.png WARNING
This is the Development page for Amahi 9 on Fedora 23.
It IS NOT production ready.


NOTES:

  • The only officially supported install media is Fedora 23 Server.
  • Ensure your system meets the minimum hardware requirements for Amahi before proceeding.
  • 32-bit installs are not available nor supported in Amahi 9.
  • NOT ALL apps available in Amahi 8 are fully operational for Amahi 9. Check the App Store before proceeding.
  • You must install Fedora 23 Server prior to installing Amahi 9.


For assistance, visit the Amahi Forums or live support on the Amahi IRC channel.

Install Fedora 23

There are two ways to install Fedora: Minimal (CD), so-called Netinstall, which is recommended, and the Full (DVD) install for cases that need more hardware support.

Minimal (CD) Install

We recommend this method for a quick download and fast installation.


  • Burn the ISO to CD (DVD or USB), insert the media into your server, and reboot the system.


  • Click [Expand] to show and [Collapse] to hide the instructions which will guide you through the Fedora 23 Netinstall CD installation with screen shots and commentary.

    NOTE: Click [Expand] below each step to show a screen shot and [Collapse] to hide it.

    Boot Screen

    • Select Install Fedora 23

      F23CD SS0.PNG


    Language Selection

    • Choose desired language and select Continue

      F23CD SS1.PNG


    Installation Summary

    • The INSTALLATION SUMMARY screen will appear. It may take a few minutes to finish Checking software dependencies

      F23CD SS2A.PNG


    • Change the KEYBOARD or TIME & DATE to match your locale if needed.

    • Once complete, next choose INSTALLATION DESTINATION. This is where you will select the disk drive to use.

      F23CD SS2B.PNG


    Disk Drive Setup

    • Choose the disk drive you want to use for the Fedora installation. If you have more than one disk drive connected, DO NOT select them at this time. You will notice a check mark on the disk drive selected. Select I will configure partitioning and then choose Done.

      F23CD SS3.PNG


    • Should you have existing partitions on the disk drive you will be using for the Fedora 23 installation, they will have to be removed.
      • You should see the existing partition about half way down the screen.

        F23CD SS3A.PNG


      • Choose it to expand and display the existing partitions for deletion. Select the first partition in the list followed by the minus (-) sign.

        F23CD SS3C.PNG


      • When prompted Are you sure you want to delete all the data on ..., choose Delete It.

        F23CD SS3B.PNG


      • Repeat the previous two steps until all the existing partitions on the disk drive are gone.

    • Ensure the New mount points will use the following partitioning scheme: is changed to reflect Standard partition. Then select Click here to create them automatically. We STRONGLY advise against use of LVM or setting a /home partition.

      F23CD SS4.PNG


    • The disk drive partition should look similar to this setup. For most users, then default partitioning scheme used will suffice. However, you can manually change it using the hard drive partition scheme documentation as a guide. Once complete, choose Done

      F23CD SS5.PNG


    • You will now see SUMMARY OF CHANGES to the disk drive. Choose Accept Changes

      F23CD SS3D.PNG


    Software Selection

    • Next on the INSTALLATION SUMMARY, select SOFTWARE SELECTION

      F23CD SS12.PNG


    • Select Minimal Install and then choose Done

      F23CD SS6.PNG


    Begin Installation

    • Back to the INSTALLATION SUMMARY and ready to begin installation. Select Begin Installation

      F23CD SS7.PNG


    Initial User Creation

    • Installation has begun and we need to create the initial user. DO NOT set the root password.

      F23CD SS8A.PNG


    • You MUST create the initial user and password (This will be your HDA Login, also called the First Admin User). Ensure you select Make this user administrator check box. Once complete, choose Done. Note that a weak password may require you to select Done twice.

      F23CD SS10.PNG


    Installation Progress

    • Now all of the configuration steps are complete. Sit back and watch the progress.

      F23CD SS11.PNG


    Installation Complete

    • Installation is complete. Choose Reboot and remove the installation media.

      F23CD SS13.PNG




Full (DVD) Install

This is only recommended for cases where the Minimal (CD) Install does not work well (e.g. if your hardware needs extra drivers).


  • Burn the ISO to DVD (or USB), insert the media into your server, and reboot the system.


  • Click [Expand] to show and [Collapse] to hide the instructions which will guide you through the Fedora 23 Server DVD installation with screen shots and commentary.
    NOTE: Click [Expand] below each step to show a screen shot and [Collapse] to hide it.

    Boot Screen

    • Select Install Fedora 23

      F23CD SS0.PNG


    Language Selection

    • Choose desired language and select Continue

      F23CD SS1.PNG


    Installation Summary

    • Change the KEYBOARD or TIME & DATE to match your locale if needed.

    • Once complete, next choose INSTALLATION DESTINATION. This is where you will select the disk drive to use.

      F23DVD SS1.PNG


    Disk Drive Setup

    • Choose the disk drive you want to use for the Fedora installation. If you have more than one disk drive connected, DO NOT select them at this time. You will notice a check mark on the disk drive selected. Select I will configure partitioning and then choose Done.

      F23CD SS3.PNG


    • Should you have existing partitions on the disk drive you will be using for the Fedora 23 installation, they will have to be removed.
      • You should see the existing partition about half way down the screen.

        F23CD SS3A.PNG


      • Choose it to expand and display the existing partitions for deletion. Select the first partition in the list followed by the minus (-) sign.

        F23CD SS3C.PNG


      • When prompted Are you sure you want to delete all the data on ..., choose Delete It.

        F23CD SS3B.PNG


      • Repeat the previous two steps until all the existing partitions on the disk drive are gone.

    • Ensure the New mount points will use the following partitioning scheme: is changed to reflect Standard partition. Then select Click here to create them automatically. We STRONGLY advise against use of LVM or setting a /home partition.

      F23CD SS4.PNG


    • The disk drive partition should look similar to this setup. For most users, then default partitioning scheme used will suffice. However, you can manually change it using the hard drive partition scheme documentation as a guide. Once complete, choose Done

      F23CD SS5.PNG


    • You will now see SUMMARY OF CHANGES to the disk drive. Choose Accept Changes

      F23CD SS3D.PNG


    Software Selection

    • Next on the INSTALLATION SUMMARY, select SOFTWARE SELECTION

      F23DVD SS2.PNG


    • Select Minimal Install and then choose Done

      F23CD SS3D.PNG


    Begin Installation

    • Back to the INSTALLATION SUMMARY and ready to begin installation. Select Begin Installation

      F23DVD SS4.PNG


    Initial User Creation

    • Installation has begun and we need to create the initial user. DO NOT set the root password.

      F23CD SS8A.PNG


    • You MUST create the initial user and password (This will be your HDA Login, also called the First Admin User). Ensure you select Make this user administrator check box. Once complete, choose Done. Note that a weak password may require you to select Done twice.

      F23CD SS10.PNG


    Installation Progress

    • Now all of the configuration steps are complete. Sit back and watch the progress.

      F23DVD SS5.PNG


    Installation Complete

    • Installation is complete. Choose Reboot and remove the installation media.

      F23DVD SS6.PNG




Install Amahi 9

Next, install Amahi 9 proper on top of Fedora 23.

You need to obtain an install code (denoted YOUR-INSTALL-CODE below) from the Amahi control panel after configuring a profile for the system you are installing, with proper network configuration for your network.

From text console or using SSH, login with the user created in the Fedora 23 installation and become root for the Amahi installation

 sudo su -

After that, type these commands in the console:

  rpm -Uvh http://f23.amahi.org/noarch/hda-release-6.9.0-1.noarch.rpm
  dnf -y install hda-ctl
  hda-install YOUR-INSTALL-CODE

NOTE: yum (deprecated) has been replaced with dnf as the Fedora package manager.

What this does is installs the Amahi F23 repo, gets the mariadb base packages to avoid dependency conflicts, and installs base Amahi packages (that part should install several packages).

If there are no errors, install Amahi (replace YOUR-INSTALL-CODE above with install code you got when creating a profile at your Amahi control panel).

If all goes well, it should tell you to reboot. Go ahead and reboot!

Once it comes back from the reboot, you should have a fully functional home server using the IP address you set up in your network!

Next you need to transition your network to use it!

Transitioning to using your Amahi server

Once installed, you will want to transition your network to using your Amahi server. Here are some of the things you should know:

  • Your server will boot with the static IP you pre-configured in the Amahi control panel
  • It's strongly recommended you follow the transition to Amahi HDA guide to get your network fully working properly
  • You can verify if the dashboard is available by accessing it from any client using the IP address of your server http://IPADDRESS/ or http://hda/ (in most Windows clients this works even without DNS from your HDA)
  • The first time it will initialize, ask you to login, and enter a dashboard password.
  • Once you reach your dashboard, you should create shares as needed, add more drives, install apps, etc., etc.
  • Optionally refer to Greyhole to install/configure storage pooling.

Troubleshooting

Visit the troubleshooting page if you find yourself in trouble.

Reference

Refer to the HDA Admin How To page for Amahi Server administrator guidance.


Go back to Amahi 9 page.